log splitter valve sticking

My new to me Countyline Speeco 25 ton splitter control valve detent mechanism was sticking operating erratically and adjusting didnt solve the problem. Quick wild guess.

2 Spool 25 Gpm Prince Log Splitter Lifter Valve Rd522ccea5a4b1 Directional Control Valves Hydraulic Valves Hydraulics Www Surpluscenter Com

First turn the log splitter over and close off the air vent remove the motor and pump 3 x 13mm headed bolts and 1 x support bolt.

. If the log splitter seems weak or not performing as it should then there is a strong likelihood that something is not right with how the splitter system is operating. The pressure may have pushed the ram forward and the splitter will not retract. If your log-splitter is moving slow but still capable of splitting the wood it always has it is most likely stuck in its second stage.

Most any hydraulic shop will have them. When attempting to split logs check that the end of the valve stem remains in contact with the face of the lever when the lever is depressed and released. If the oil is found to be enough then the problem is due to the air mixed with liquid when opening the bleed valve and cycling pressure plate.

Now release the ram and put back the oil-filling plug. Common problems with AL-KO and similar Chinese generic log splitters the hydraulic valve spindle breaks on the end stopping the unit from working correctly. Its a Huskee 22 ton and the valve is sticking both ways.

The frame generator burn plate collar and burn tube assembly. Anyone ever rebuild a log splitter hydaulic valve. In the second stage or low flowhigh-pressure stage the pump produces 25 or less of its rated GPM but it does it at a higher pressure.

If a log is not splitting all the way through then the log may be too green or too large meaning that it would require a greater force than your log. When you forced the spool back to center you finished destroying the o-ring and now it leaks. In this stage.

Return Detent on Log Splitter Valve in reply to wsmm 09-25-2013 111353 Hello WSMM. Once the frame is removed youll be holding several pieces. Other than that it works fine.

And it simultaneously allows oil from the rod-end port of the cylinder to flow into. Check the manual to be sure you have proper lever position. That should be easy to fix.

You can check for this issue easily. Note the force used. Dec 12 2005.

Valve core requires cleaning. If fluid is leaking from your pump disassemble it and replace all seals. Pushed one way it shunts oil from the pump to the base port of the cylinder causing it to extend.

On one side of the valve there is a inch long bolt only way I know how to describe it with a ball in the end. If the valve core does not pop back out when the lever is released then it requires cleaning. This will remove all the excess air trapped inside the splitter.

Having a two stage pump and the automatic detent valve that my store built splitter has puts the single stage pump and non-detent valves to shame for ease of use. The o-ring sealing the spool to the valve body got damaged and caused the spool to stick. I have a Brave Log splitter and the last few weeks the detentspoil valve has become sticky after the I split a couple of hours.

The hydraulic valve has seals around the actuator rod that can wear out and fail over time. Start your adjustment in small increments while re-testing the resistance until it takes just a small snap to pop it into center. No power to the motor Fuse blown or RCD Tripped.

When the pump fails it will often send metal debris. The spool shifted by the handle has 3 positions. Up to 32 cash back The log splitters hydraulic control valve directs the hydraulic fluid flow to the hydraulic cylinder to extend and retract the piston and wedge.

Check the position of the lever. Remove the spool and get a replacement o-ring. You need to check the amount of oil first.

Check the position of the lever. The project will include refurbishment of the towns two water storage tanks at a cost of 477000 and installation of 25 automatic meters and. What would you recommend.

Another reason for a slowed-down log splitter is a jammed motor due to blockage in the fan. Lock the handle into the return position and manually pull it back into center position. Here in Tech Support we receive calls from Rapid-Fire Log Splitter owners regarding a vibration or chatter that occurs while operating their machineThere.

This tutorial apply to the Energy control valve. If youre used to the lever going one way on one log splitter you might have overlooked the valve position on a different log splitter that works differently. If still your log splitter shuts off under load most likely your hydraulic pump is jammed or stuck in its high flowlow-pressure stage described as the first stage.

Ensure that the ram is fully returned this is essential before starting the process. A detent valve lever can be pushed up or down to put the valve into operation. If not then look for blockages in the fan and remove them.

The hydraulic directional valve controls the motion of the cylinder. To begin with check your log splitter and the wood you are trying to split. Remove the fan cover and try to turn it to see if it moves without difficulty.

Also it is hard to trip the lever to get it to stop retracting. Read about gas log splitter. Now start up the engine and give it a try.

Kshansen May 21 2020 19. Remove the air from the system to solve this problem and keep the bleed valve tightened enough. Fixing the auto-return on a hydraulic control valve usually is just a matter of tightening The bolt inside the detent cover assembly.

This valve is the most prevalent valve used in the residential log splitter industry. The detent cover on the hydraulic valve controls the auto-return. Just rotate clockwise the oil-filling plug and remove the plug.

I pulled the cap and found it contaminated with moisture and it was lubricated with a silver pastegrease. If hydraulic fluid leaks from the valve body around the actuator rod replace the hydraulic valve in the log. And now it started to stick going out and it will go out to the end and stall the engine.

First turn the log splitter over and close off the air vent remove the motor and pump 3 x 13mm headed bolts and 1 x support bolt. Place the log splitter back upright and try the splitter again if it produces the same noise then loosen the bolts a little from the end of the pump 13mm and try again. The seals on these pumps wear over time and eventually can cause hydraulic fluid to leak out of the system.

When it retracts it pulls in tight and stalls the engine. The Hydraulic Log Splitter Valve. When repairing a damaged pump it is important to carefully analyze and address the rest of the hydraulic system.

Drop the frame burn plate burn tubes collar and ball nut into.

25 Fix Log Splitter Hydraulic Control Valve O Ring Rebuild Youtube